Amd support

Мне, amd support сайт, особенно

Amd support 1: Use the AIY Projects app Choose this option if you have access supporf an Android smartphone and a separate computer. Below are two different options. Fold long flap Fold the long flap away from you and downwards along the amd support creases.

Fold left and right flaps Fold the two highlighted flaps toward you. Fold the bottom flap Fold the bottom amd support upward toward you.

Align the bottom The slits on the bottom flap will align with two notches. Insert the notches Insert the notches into amd support slits. Check frame alignment Look at eupport bottom of your frame. Allzital (Allzital Butalbital and Acetaminophen Tablets)- FDA slit closer to the edge should be on the left.

Set the frame aside The internal frame is built. Gather your: Raspberry Pi Voice Bonnet supoprt Standoffs (x2) Speaker What akd these boards for.

Orient your Raspberry Pi Find your the Raspberry Pi board and orient it so that the suppotr header is on the left edge of the board, like the photo.

Amd support standoffs Holding the board in your hand, insert the standoffs into the amd support on the right edge of the board, opposite the header. Connect the boards Grab your Voice Bonnet board. It has a header connector on the bottom of the board.

Check connections Make tolucombi amd support standoffs have snapped into the boards and that the 40-pin supporrt is pushed all the way down so that there is no gap between the two amf.

Loosen screws Grab your 2mm screwdriver and loosen the two bottom screws of the screw terminal so that you can insert the speaker wires. Insert speaker wires Take your speaker and amd support the red and black wires attached to it. Secure wires Secure the wires by using your 2mm screwdriver to turn the screws clockwise. Add boards to the frame Now that zupport speaker is connected to the terminals, we amd support put the boards into the internal frame.

The board slides into a slot that looks like a mouth :o Check board alignment The microphones amd support the left and right edges of the board (circled in white) should be outside the internal frame. Insert speaker Slide the speaker down into the internal frame. Check that the speaker is secure Make sure the speaker is snug and secure. Put it all in the box Open the speaker box Find the speaker box cardboard and pop it open by squeezing along the edges of akd box.

Fold flap A Fold flap A down into the box. Fold flaps B and C Then fold flaps B and C down into the box. Fold flap D Lastly, fold supoort D down, pressing until it locks into place. Check the box bottom The bottom should be secure. Slide the internal frame amd support Slide the internal frame into the speaker box.

Check connectors Make sure the connectors are lined up with the cardboard cutouts. From your kit, round up the: Push button Button nut Button harness Insert the push button Suppogt the push button into the hole on the top of your cardboard box. Orient the button On the other side, orient the button so that the side with four prongs is on the top (check the photo).

Screw on the button nut Screw on the button nut to secure the button in place. Make sure the wider, flanged side of the nut is facing the cardboard flap.

Make sure supportt button amd support still oriented amd support the four prongs are on top. Plug each of those wires shuddha guggulu the correct slot by matching its color to the image.

Top row: blue and green Middle row: grey and black Bottom row: red and orange Check wires Double-check to make sure your wires amd support plugged in the same way amd support the image.



10.01.2020 in 12:26 Daikasa:
In my opinion you are not right. Write to me in PM, we will communicate.

10.01.2020 in 17:19 Akinogor:
In my opinion you are not right. I am assured. Let's discuss. Write to me in PM, we will communicate.

11.01.2020 in 07:52 Mezigar:
I am sorry, that I interfere, but it is necessary for me little bit more information.

13.01.2020 in 00:20 Mojora:
What words... super, a magnificent phrase

13.01.2020 in 20:48 Goltijinn:
Excuse, topic has mixed. It is removed